Tips & Tricks | IS & VR Lens Care images

Image stabilisation is a common feature on modern lenses, giving up to 4 stops advantage,  and we’ve all enjoyed the benefits in those tricky low light situations where we don’t want to push the ISO too far.

The principle behind the technology is similar, regardless of manufacturer. A group of floating elements positioned near the rear of the lens are held in place by a series of electro-magnetic coils. Two gyroscopic sensors detect horizontal and vertical movements, and corrective adjustments are relayed to the electro-magnets which in turn steady the floating elements, resulting in a much sharper and steadier image.

The IS unit from a Canon 100-400mm ƒ/4.5-5.6L IS lens.

Now with all this electronic technology sitting in the lens – effectively a mini computer – it goes without saying that care should be taken with your glass, especially as the stabilisation systems can be easily damaged if care isn’t taken when removing the lens.

When the lens is attached to the camera and powered on, the electro-magnets release the elements, ready to stabilise the shot once the AF is activated. But when the camera is turned off, the power to the electro-magnets is deactivated and the elements lock in place to minimise any damage if the lens is knocked.

However, if the lens is removed before the elements have a chance to lock, they can float around freely and are susceptible to damage. The golden rule here is to ensure the camera is turned off and wait a couple of seconds to allow the elements to lock before removing the lens. On some lenses an audible click can also be heard when locking.

In some Nikkor lenses, the VR unit can be replaced without having to replace the floating element group. This example is from a 70-200mm ƒ/2.8G (1st Gen).

Lenses with damaged stabilisation units are something we see every week in the workshop and replacing these units can run into several hundred pounds, depending on the lens.

 

10 Replies to “Tips & Tricks | IS & VR Lens Care”

  1. My film and digital Nikon bodies advise the user to switch off the body before mounting/exchanging lenses. This posted note helps to explain why.

  2. I had an IS problem last year which was fixed by you, I’ll be more careful in the future!! Thanks for the advice

  3. Thanks for the useful information.

  4. I’m also very skeptical of this advice. Are you suggesting that I may potentially cause damage by walking around with the camera on ? Because there’s considerably more movement with a camera around the neck or waist then simply holding it to remove the lens off its mount.

    1. Hi Frank

      Almost the opposite in fact! We were simply highlighting the potential problems if the lens is removed while the image stabilisation is still ‘on’. You can quite happily leave your camera turned on, with a lens mounted.

  5. Thanks for the advice.

    I assume from your article that turning VR off on the lens is not the same as turning the camera off, but should be grateful if you would confirm.

    1. Hi Rob

      Generally speaking, best practice is to turn the camera off and wait for the VR to ‘lock’, rather than turning VR off on the lens.

  6. I’ve never heard of this before. Researched on lots of forums and most have always said it’s okay to leave camera on, albeit that this wasn’t specific to IS lenses. Glad I found out about this, but surprised it isn’t common knowledge- do the manuals warn about this?

    1. Hi Matt

      We’re not sure if it’s mentioned in any manuals, but both Nikon and Canon have mentioned this online as a potential problem:

      Nikon article: https://www.nikonimgsupport.com/ni/NI_article?articleNo=000002988&configured=1&lang=en_US
      Canon article: http://learn.usa.canon.com/resources/articles/2014/is_lens_rattling.shtml

      Hope this helps 🙂

      1. Thank you. VERY grateful to know about this!!

Leave a Reply

Your email address will not be published.

You may use these <abbr title="HyperText Markup Language">HTML</abbr> tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <s> <strike> <strong>

*

Hi, how can we help?